DESIGN AND CONSTRUCTION OF A PUBLIC ADDRESS SYSTEM (PA SYSTEM) WITH A.C AND BATTERY POWER SOURCE
USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a public address system (pa system) with a.c and battery power source" Please, sit back and study the below research material carefully. This project topic "design and construction of a public address system (pa system) with a.c and battery power source" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a public address system (pa system) with a.c and battery power source" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a public address system (pa system) with a.c and battery power source" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
DESIGN AND CONSTRUCTION OF A PUBLIC ADDRESS SYSTEM (PA SYSTEM) WITH A.C AND BATTERY POWER SOURCE
BY
---
EE/H2013/01430
DEPARTMENT OF ---
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work, "design and construction of a public address system (pa system) with a.c and battery power source" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on Electrical and Electronics Engineering has been approved.
By
Dr. --- Dr. ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
Dr. ---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work “design and construction of a public address system (pa system) with a.c and battery power source” research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of “design and construction of a public address system (pa system) with a.c and battery power source” visible for everyone, then the complete material on “design and construction of a public address system (pa system) with a.c and battery power source” is to be ordered for. Happy viewing!!!
This work is titled design and construction of a public address system with ac and battery power source. A public address system (PA system) is an electronic sound amplification and distribution system with a microphone, amplifier and loudspeakers, used to allow a person to address a large public, for example for announcements of movements at large and noisy air and rail terminals.Public addressing system is often used in small venues such as school auditoriums, churches, and small bars. PA systems with many speakers are widely used to make announcements in public, institutional and commercial buildings and locations. Intercom systems, installed in many buildings, have microphones in many rooms allowing the occupants to respond to announcements.This system was built using some major electronics components such as transistor, resistor, capacitors, and an aluminum heatsink was used to protect the power transistors from overheating.This Public Addressing Systems have a potential for audio feedback, which occurs when sound from the speakers is picked up by the microphone and is then re-amplified and sent through the speakers again. That makes it to sounds like a loud high-pitched squeal or screech, and can occur when the volume of the system is turned up too high.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
- PROBLEM STATEMENT
- AIM/OBJECTIVE OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- APPLICATION OF THE PROJECT
- PROJECT JUSTIFICATION
- SCOPE OF THE PROJECT
- LIMITATION OF THE PROJECT
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- REVIEW OF PUBLIC ADDRESSING SYSTEM
- HISTORICAL BACKGROUND OF PUBLIC ADDRESSING SYSTEM
- DIFFERENT TYPES PUBIC ADDRESSING SYSTEM
- DIFFERENT TYPES PUBIC ADDRESSING SYSTEM
- CLASSIFICATION OF AMPLIFIERS
- CHARACTERISTICS OF ACTIVE COMPONENTS
CHAPTER THREE
METHODOLOGY
- INTRODUCTION
- FEATURES AND SPECIFICATIONS OF THE AUDIO AMPLIFIER SYSTEM
- BLOCK DIAGRAM
- DESIGN STAGES
- AMPLIFIER CIRCUIT DIAGRAM
- CIRCUIT DESCRIPTION
- AMPLIFIER CIRCUIT OPERATION
- POWER SUPPLY
- CALCULATION
CHAPTER FOUR
- PROJECT IMPLEMENTATION AND CONSTRUCTION
- CONSTRUCTION
- DESIGNING OF THE SCHEMATIC AND LAYOUT DIAGRAM
- TOOLS AND EQUIPMENT
- MOUNTING AND SOLDERING OF THE COMPONENTS ON THE PRINTED CIRCUIT BOARD
- CONSTRUCTION OF CASING
- PRECAUTION
- PROBLEMS ENCOUNTERED
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFERENCES
CHAPTER ONE
- INTRODUCTION
In general, the purpose of an amplifier is to take an input signal and make it stronger. Amplifiers find application in all kinds of electronic devices designed to perform numbers of functions. There are many different types of amplifiers, each with a specific purpose. This project is specified on audio amplifier. Audio power amplifiers are those amplifiers which are designed to drive loudspeakers.
Scientifically, a public address system is an electronic device in which a small-signal vibration is amplified using pre-amplifier(s); this signal (audio frequency signal) is then amplified to a level required to drive a loudspeaker by a power amplifier.
1.1 BACKGROUND OF THE PROJECT
A public address system comprises electrical equipment to greatly amplify a speaker's voice so it will reach a much larger assemblage than he could speak to unaided. Beginning with the presidential conventions of the two major parties in 1920 and the inaugural address of President Harding in March 1921, when a special address system installed by the telephone engineers enabled him to address an audience estimated at 125,-000, there followed in rapid succession, many public events demonstrating the value of such systems. One of the most notable of these occurred on Armistice Day 1921, when the speeches, prayers and music at Arlington, Virginia, were heard, not only by 100,000 persons gathered there at the National Cemetery, but by some 35,000 in New York City and 20,000 in San Francisco. On this occasion the three public address systems, one for each of these cities, were joined by long distance telephone circuits.
The fundamental requirements of a satisfactory public address system are naturalness of reproduction and wide range of output volume. The meeting of these two requirements for music proves more difficult than for speech.
The public address system here described is most readily considered in three sections—“pick-up” apparatus which is placed in the neighborhood of the speaker and converts his words into undulatory electric currents; a vacuum tube amplifier for amplifying these currents; and a “receiver-projector” for reconverting the current into sound waves and distributing the sound over all of the audience. In the present system each of these three parts of the equipment has been designed with the intention of making it as nearly distortionless as possible, so that the various parts might be adaptable for audiences ranging in size from possibly one thousand to several hundred thousand, and might also be used in connection with the long distance telephone lines and with either radio broadcasting or receiving stations. One of the larger public address systems is easily capable of magnifying a speaker's voice as many as 10,000 times.
The pick-up device whether of the carbon microphone variety or a condenser transmitter need not be placed close to the speaker's lips but will operate satisfactorily when four or five feet away. The loud-speaking receiver mechanism is so designed that it will carry a power of several watts with small distortion. Under normal conditions, 40 watts distributed among a number of receiver-projectors arranged in a circle is ample to reach an audience of 700,000 persons.
1.2 PROBLEM STATEMENT
This project is to overcome communication problems that usually occur in areas where it is hard to find a device for making important announcements or speeches so that everyone can listen precisely to what the speaker is talking about. This simple project may also be used by lecturers in lecture halls to bridge communication gap between the lecturers and student in a lecture, as shouting during lectures may be very exhausting.
1.3 AIM AND OBJECTIVE OF THE PROJECT
The objective of this work is to construct an electronic sound amplification and distribution device with a microphone, amplifier and loudspeakers, used to allow a person to address a large public, for example for announcements of movements at large and noisy air and rail terminals, with ac and battery power source which prevents the device from power interruption. This project should not be bulky in size.
- Acquaint with the use of basic Electronic Components and devices
- Strengthen capacity for a better audience
- Increase or magnify a low energy level signal (in this case sound).
- Improve communication
- Understand Basic Principles of Amplifiers.
1.4 SIGNIFICANCE OF THE STUDY
Public addressing system is often used in small venues such as school auditoriums, churches, and small bars. PA systems with many speakers are widely used to make announcements in public, institutional and commercial buildings and locations.
1.5 APPLICATION OF THE PROJECT
Public addressing system is often used in small venues such as school auditoriums, churches, and small bars. PA systems with many speakers are widely used to make announcements in public, institutional and commercial buildings and locations. Public addressing system is naturalness of reproduction and wide range of output volume. The meeting of these two requirements for music proves more difficult than for speech.
1.6 PROJECT JUSTIFICATION
Over the ages, science and technology has been developing with new inventions in various fields; including the increase in modifications on existing technology all gearing towards improving effectiveness and reliability of equipment and achieving to a great degree miniaturization and optimal cost.
This project is backed by my interest in the area of electronics and communication, and having been groomed to a great extent with introductions into the various fields of electrical and electronics engineering, with the knowledge in principles of telecommunications, telecommunication engineering.
1.7 SCOPE OF THE PROJECT
This system is for public address; it has an estimated power rating of 20watts. For power supplies, it uses a 220/12Vac transformer for the AC supply and a rechargeable 12v battery for the DC supply used in supplying power to the receiver, amplifier and loudspeaker units. It has a power On/Off button with volume control.
After designing all sub circuits, the PCB of each sub circuit is constructed. The project ends up with the combination of all sub circuits and troubleshooting should there be any problem.
1.8 LIMITATION OF THE PROJECT
INTERFERENCE: Interference can be a problem. There are lots of devices that emit radio waves. If those radio waves are on the same frequency as with the transmitter and receiver, you could get some garbled signals as you listen to the output. Dropped signals can also be an issue -- if a transmitter or receiver stops working or drops out, it will affect your listening experience.
BANDWIDTH: Another problem is bandwidth. Wired PA can carry a lot of information in the form of electrical signals. Audio may seem less full or rich. It's a subjective element that can be difficult to put into words.
Another drawbacks of public addressing (PA) systems is the cabling that is required, which can be expensive, difficult and time-consuming to install. A wired PA system suffers from a number of drawbacks, that is to say: being "fixed" - it being difficult to relocate the speakers subsequent to installation; loss of operation and/or functionality in the event of one of more of the cables failing; and loss of operation and/or functionality in the event of a power outage.
Different power source, that is, a 12v battery and an ac power source. The battery power source is used to power the system during the electricity outage.
1.9 PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to the public address system. In this chapter, the background, significance, objective limitation and problem of public address system with dual power supply were discussed.
Chapter two is on literature review of power restoration reminder. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
CHAPTER ONE: The complete chapter one of “design and construction of a public address system (pa system) with a.c and battery power source” is available. Order full work to download. Chapter one of “design and construction of a public address system (pa system) with a.c and battery power source”consists of the literature review. In this chapter all the related work on“design and construction of a public address system (pa system) with a.c and battery power source” was reviewed.
CHAPTER TWO: The complete chapter two of “design and construction of a public address system (pa system) with a.c and battery power source” is available. Order full work to download. Chapter two of “design and construction of a public address system (pa system) with a.c and battery power source” consists of the literature review. In this chapter all the related work on “design and construction of a public address system (pa system) with a.c and battery power source” was reviewed.
CHAPTER THREE: The complete chapter three of “design and construction of a public address system (pa system) with a.c and battery power source” is available. Order full work to download. Chapter three of “design and construction of a public address system (pa system) with a.c and battery power source” consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of “design and construction of a public address system (pa system) with a.c and battery power source” is available. Order full work to download. Chapter four of “design and construction of a public address system (pa system) with a.c and battery power source” consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of “design and construction of a public address system (pa system) with a.c and battery power source” is available. Order full work to download. Chapter five of “design and construction of a public address system (pa system) with a.c and battery power source” consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
You can also visit our facebook Page at fb.me/hyclas to view our related construction (or design) picture.
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
COUNTRIES THAT FOUND OUR SERVICES USEFUL
Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.